Fix Automatic Repair Loop in Windows 10

      No Comments on Fix Automatic Repair Loop in Windows 10

A client recently mentioned that his Windows 10 Laptop was stuck in an Automatic Repair Loop. As he switched on the PC, it developed the “Preparing Automatic Repair” screen and after that rebooted automatically and ran Automatic repair again, becoming caught knowledgeable all the time.fix automated repair loop

There may be a lot of reasons for any failed automatic repair. However, the most prevalent issue is a corrupted registry or missing files to the hard disk. This I can give the overall solutions regarding how to fix this problem in Windows 10, 8.1, and 7.

All of the solutions below need you to run certain commands in the Command Prompt. This is a means to access the Command Prompt at boot:

  1. Insert your Windows installation DVD, switch on the PC, and wait until you can see your message “Press any key to boot from CD or DVD”. Just press any key to continue. (Note: Should you don’t check this out a message, you most likely replace the boot order inside BIOS).
  2. After some time, you’ll get through to the Windows Setup screen. Press Shift + F10 to open up a Command Prompt.Fix Automatic Repair Loop

Solution 1: Running check disk to see if your hard drive is the problem

Chkdsk might be utilized to check and repair your hard drive for file system corruption. Before you run the chkdsk command, you need to find out of the drive letter to your system drive. For the way your system is setup, this might be either C: or D:.

  1. Type dir C:\ and press Enter.
  2. If you notice the common folders: Program Files, Users, and Windows, then you’ve found the system drive.fix automated repair loop

 

When the drive isn’t the system drive, repeat the step-above, changing the drive letter to D, E or other letters so that the system drive located.

When you’ve got located your Windows system drive, type as follows command and press Enter. Replace D: while using the actual drive letter of the system drive.

chkdsk d: /ffix automated repair loop

 

The scan should start. This might take a few hours based on the sized your hard drive. When the scan is finished, exit the Command Prompt and reboot your PC to find out if the issue may be solved.

Solution 2: Manually attempt to rebuild the BCD and repair MBR

Running the bootrec utility to rebuild the BCD / MBR might fix the automated repair loop problem. Type as follows kind of commands in the Command Prompt, individually.

bootrec /fixmbr

bootrec /fixboot

bootrec /rebuildbcdfix automated repair loop

The /fixmbr switch writes a brand new MBR (Master Boot Record) somewhere partition, the /fixboot switch writes a whole new boot sector on the system partition, and also the /rebuildbcd switch scans all disks for Windows installations and gives a selection of which entries to increase the BCD store.

Solution 3: Disable Automatic Startup Repair

When the automatic repair couldn’t really repair your computer and simply take you stuck in the repair loop, it’s far better to disable the automated startup repair. Type as follows command and press Enter:

bcdedit /set (default) recoveryenabled Nofix automated repair loop

Now you’ve successfully disabled the automated startup repair feature in Windows.

Solution 4: Restore your Windows Registry

A corrupted registry setting may also make an auto-repair loop. Here’s how to recover your registry through the Regback directory. The Regback folder is found in :/windows/system32/config, that is utilized by Windows to keep a current backup copy in the registry hives.

Assuming the system drive is d: run as follows command to recover Windows registry:

copy d:\windows\system32\config\Regback\* d:\windows\system32\configfix automated repair loop

If prompted to overwrite existing files, type All thus hitting Enter. Type exit and hit Enter to close the Command Prompt Window. Restart your PC and many probably, you could capable of access your Windows system as before.

I hope the solution here help you to fix Automatic Repair Loop in Windows 10. If you don’t know or are still confused about the way in this article about fix Automated Repair Loop, please write in the comment section. Please share this article to your social media so that friends or people who experience the same problem can read this article. Thank you for visiting our website.

Leave a Reply

Your email address will not be published. Required fields are marked *